Alcatel 9000 Betriebsanweisung PDF herunterladen (Seite 58)

100

101

Setting Combo Ethernet Port Parameters on OmniSwitch 6800 and 6850 Switches Configuring Ethernet Ports

page 1-22 OmniSwitch 6800/6850/9000 Network Configuration Guide June 2006

copper, duplex, and the desired duplex setting (auto, full, or half). For example, to set the duplex mode

on fiber combo ports 45 through 48 on slot 2 to full, enter:

-> interfaces 2/45-48 hybrid fiber duplex full

As an option, you can document the interface type by entering ethernet, fastethernet, or gigaethernet

before the slot number. For example, to set the duplex mode on the fiber combo port 47 on slot 2 and

document the fiber combo port as Gigabit Ethernet, enter:

-> interfaces gigaethernet 2/47 hybrid fiber duplex full

Configuring Autonegotiation and Crossover for Combo Ports

The following subsections describe how to enable and disable autonegotiation (see “Enabling and

Disabling Autonegotiation for Combo Ports” on page 1-22) and configure crossover settings (see “Config-

uring Crossover Settings for Combo Ports” on page 1-23) on combo ports.

Enabling and Disabling Autonegotiation for Combo Ports

By default, autonegotiation is enabled. To enable or disable autonegotiation on a single combo port, a

range of combo ports, or all combo ports on an entire slot, use the interfaces hybrid autoneg command.

(See “Configuring Crossover Settings for Combo Ports” on page 1-23 for more information).

Note. In the interface hybrid autoneg command, the copper keyword is used to configure the copper RJ-

45 10/100/1000 port while the fiber keyword is used to configure the fiber MiniGBIC SFP port.

To enable or disable autonegotiation on all combo ports in an entire switch, enter interfaces, followed by

the slot number, hybrid, either fiber or copper, autoneg, and either enable or disable. For example, to

enable autonegotiation on all copper combo ports on slot 2, enter:

-> interfaces 2 hybrid copper autoneg enable

Note. using the interface hybrid autoneg command to set all combo ports on a switch will not affect the

configurations of the non combo ports.

To enable or disable autonegotiation on a single combo port, enter interfaces, followed by the slot

number, a slash (/), the combo port number, hybrid, either fiber or copper, autoneg, and either enable or

disable. For example, to enable autonegotiation on copper combo port 47 on slot 2, enter:

-> interfaces 2/47 hybrid copper autoneg enable

To enable or disable autonegotiation on a range of combo ports, enter interfaces, followed by the slot

number, a slash (/), the first combo port number, a hyphen (-), the last combo port number, hybrid, either

fiber or copper, autoneg, and either enable or disable. For example, to enable autonegotiation on copper

combo ports 45 through 48 on slot 2, enter:

-> interfaces 2/45-48 hybrid copper autoneg enable

As an option, you can document the interface type by entering ethernet, fastethernet, or gigaethernet

before the slot number. For example, to enable autonegotiation on copper combo port 47 on slot 2 and

document the combo port as Gigabit Ethernet, enter:

-> interfaces gigaethernet 2/47 hybrid copper autoneg enable

1 2 ... 53 54 55 56 57 58 59 60 61 62 63 ... 701 702

Kommentare zu diesen Handbüchern

Keine Kommentare

Alcatel 9000 Betriebsanweisung Seite 58

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Software Alcatel 9000